what is best way to install hardware on cabinets

April 07, 2022 Post a Comment

Last Updated: July 2, 2021

Click higher up to sentinel the video

So, you spend all of that fourth dimension building or refinishing a set of cabinets and now yous're faced with 7000 handles that take to exist put on…each one measured and placed, evenly. Have no fear, I'm going to bear witness you both how to manually install a handle and then brand a ridiculously unproblematic jig based on that installation that will allow you lot wing through the rest of the handles.

Manual Handle Install

We get-go by installing our handle straight and even in the position we want information technology. This will deed equally a template for the jig, too. Carefully measure the altitude between the threaded ends of the handle. This is the altitude between the holes you will drill .

I similar to put masking tape across the face up of the drawer (so I don't marking all over the drawer, itself). Detect and mark the center of the drawer front, both, forth the width and the length.

Now, measure out out from that centerline, both left and right, half the distance you lot but measured on the handle, and make a marker. The center of your handle goes right on the centerline of the drawer face (bold you're mounting the handle expressionless-center).

Measure down from the height of the drawer at each mark and make another marker creating a crosshair. You lot should now have a mark for both the width and length locations crossing each other at the exact point the hole should be drilled.

If you aren't using a brad point drill bit (a bit with a point on the cease), then use an awl to start each hole. Regular twist bits have a flatter end, tend to "skate" around before digging in, and can be inaccurate.

Drill each hole without using too much pressure. Let the bit exercise the piece of work and forestall tear out on the backside.

Many times the bolts that come with the handle will have sections. These are meant to be cutting at a given section depending on the length you demand and avoid trigger-happy up the threads. Otherwise, they should come up with ii unlike sizes of bolts.

Making the Drawer Jig

This jig can exist fabricated from nearly whatever scrap forest y'all can find. I've used all different thicknesses and types. In the video to a higher place, I used some chip 3/4" plywood I had laying around.

We'll make the drawer jig first. The front end piece should exist wide enough and long enough to hang from the top of the drawer and spread across the surface area where the handle will be installed on the longest drawer you lot take.

Cut a 1 1/two" strip and glue information technology to the top to deed every bit a "shoe" that will register on the acme of the drawer front end. The parts are glued and nailed in place. Make sure the border of the shoe is flush with the edge of the confront then that the jig will have enough depth to register on the drawer and withal hang down.

Measure and marker the center of the jig. This marker will line upwards with a marking you lot make on the center of each drawer. Once those marks are lined up, yous know the jig is in position.

Put the jig in identify on the drawer you previously drilled holes in and secure it. Yous can clamp it in identify or just concur it firmly, only make sure information technology doesn't move around. Drill through the holes from the back into the jig.

This technique will let you to use the jig for multiple different sizes. I marked over each set up of holes with a different colored marker to differentiate between them and avoid getting confused.

Now, you're gear up to employ the jig on the remaining drawers. Simply measure the center of the drawer and make a calorie-free mark on summit of the drawer front, put the jig in place, and carefully drill the holes.

Making the Door Jig

The door jig is fabricated in much the aforementioned manner, simply with different measurements. Follow the same process as above to manually install the commencement handle.

The door jig will have the same ane one/2" shoe that registers on the border of the door, just it also has a shoe that registers on the lesser. This allows the door jig to quickly hook onto the corner of the door and leave no doubt about its right position. I made the face of the jig 2 one/4" broad to cover the width of the confront frame and all of the pieces are flush on the outer face. I assembled the door jig together with gum and brad nails.

I made two door jigs, one for right swinging and one for left swinging. You don't accept to practice it this way since i jig can simply be flipped effectually and drilled from the backside on the opposite swinging door. I was having problem with tear out on the drawers, so I made both since they're and so easy. I ended upwardly not having problem with tear out on the solid wood doors, so i jig would piece of work just fine. I drilled holes for two different sizes of door handle into the door jig, too.

The jig works the same manner for lower doors as information technology does for the upper. Plough it upside down and hook it on the tiptop corner of the lower door.

This is one of those extremely quick and direct-forward jigs that tin relieve you hours of time. Reading about how to do this can be disruptive, and then watch the video for a more than illustrative tutorial.